Добрый день! С некоторых пор перестал грузиться маршрутизатор 1841. входит в rommonitor нормально, но когда делаешь tftpdnld пишет:
get_mac_address(): Search T_IDPROM_MACADDR (0xc3) fai
led Illegal MAC address.
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_PORT: 0= (default), 1
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
4=Auto (default)
Command line options:
-h: this help screen
-r: do not write flash, load to DRAM only and launch image
Если делаешь xmodem то:
rommon 25 > xmodem -c 1841
Do not start the sending program yet...
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
File size Checksum File name
0 bytes (0x0) 0x0000 ervicesk9-mz.124-3a.bin (invalid)
0 bytes (0x0) 0x0000 (invalid)
0 bytes (0x0) 0x0000 (invalid)
0 bytes (0x0) 0x0000 (invalid)
0 bytes (0x0) 0x0000 (invalid)
WARNING: All existing data in flash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
Ready to receive file 1841 ...
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
Format: Drive communication & 1st Sector Write OK...
Writing Monlib sectors.
................................................................................
..................
Monlib write complete
Format: All system sectors written. OK...
Format: Operation completed successfully.
Format of flash: complete
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
Download Complete!
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x1002850
Self decompressing the image : #################################################
################################################################################
####################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X0013 0X00035000 Card in slot 0
0X0037 0X00035000 Card in slot 1
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 6616595 bytes to IO Memory.
PMem allocated: 118489088 bytes; IOMem allocated: 15728640 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-ENTBASE-M), Version 12.4(7), RELEASE SO
FTWARE (fc6)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 28-Feb-06 21:03 by alnguyen
Image text-base: 0x600893C8, data-base: 0x61900000
после этого висит.
В чем может быть дело?
