Исходное сообщение
"Cisco 2621XM" Отправлено merax, 14-Мрт-08 13:38
Помогите вот с таким вопросом. Имеется циско 2621 в локальной сети. В ети есть внешний шлюз с адресом 192.168.53.1. В циско имеется модуль ADSL. Необходимо зарезервировать основной канал (Локальная сеть) на ADSL. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Ukb_urai ! boot-start-marker boot-end-marker ! logging buffered 32000 debugging enable secret 5 $1$mlNa$NTfXQL4QN4QzuatNtxlE8/ enable password angel ! aaa new-model ! ! ! aaa session-id common ! resource policy ! no network-clock-participate slot 1 no network-clock-participate wic 0 ip cef ! ! ! ! vpdn enable ! vpdn-group pppoe ! vpdn-group pptp ! Default PPTP VPDN group accept-dialin   protocol pptp   virtual-template 2 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller E1 0/0 framing NO-CRC4 channel-group 0 timeslots 1-2 ! controller E1 0/1 framing NO-CRC4 channel-group 1 timeslots 1-2 ! ! bridge irb ! ! bba-group pppoe global ! ! interface FastEthernet0/0 no ip address speed auto full-duplex pppoe enable group global ! interface FastEthernet0/0.20 ! interface FastEthernet0/0.41 ip nat inside ip virtual-reassembly no ip mroute-cache pppoe enable group global no keepalive no cdp enable ! interface FastEthernet0/0.44 description -==== Remote Office vlan 44 ===- encapsulation dot1Q 44 ip address 192.168.44.2 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.51 ! interface FastEthernet0/0.53 description -=== Link to LOCAL_NET ====--- encapsulation dot1Q 53 ip address 192.168.53.2 255.255.255.0 ip nat inside ip virtual-reassembly no snmp trap link-status ! interface ATM0/2 no ip address no atm auto-configuration no atm ilmi-keepalive no atm address-registration no atm ilmi-enable dsl operating-mode auto ! interface ATM0/2.1 point-to-point no snmp trap link-status pvc 1/50   encapsulation aal5snap   pppoe-client dial-pool-number 1 ! ! interface Virtual-Template1 ip unnumbered FastEthernet0/0.53 ip access-group LOG in ip access-group LOG out ip tcp header-compression peer default ip address pool pool_pppoe ppp authentication ms-chap-v2 chap ! interface Dialer1 ip address negotiated no ip unreachables no ip proxy-arp ip mtu 1492 ip nat outside ip virtual-reassembly encapsulation ppp ip policy route-map NAT dialer pool 1 no cdp enable ppp authentication chap pap callin ppp chap hostname **** ppp chap password 0 ********* ppp pap sent-username **** password 0 ********* ! interface BVI1 no ip address ! ip route 0.0.0.0 0.0.0.0 192.168.53.1 ip route 0.0.0.0 0.0.0.0 Dialer1 ip route 192.168.44.0 255.255.255.0 192.168.53.1 ip route 192.168.50.0 255.255.255.0 11.0.0.2 ip route 192.168.51.0 255.255.255.0 FastEthernet0/1 ip route 192.168.53.0 255.255.255.0 11.0.0.2 ! ! ip http server ip http secure-server ! ip access-list standard mfUkb deny   any permit any ! access-list 115 permit ip 0.0.0.102 255.255.255.0 any access-list 133 permit tcp host 192.168.53.102 any eq telnet access-list 133 permit tcp host 192.168.53.190 any eq telnet access-list 133 deny   tcp any any ! snmp-server community public RO ! route-map NAT permit 10 match ip address 115 set interface Dialer1 ! ! ! control-plane ! bridge 1 protocol ieee bridge 1 route ip Направте хотя бы на путь истинный. Заранее благодарен.