- SHDSL,
 Volume, 15:48 , 20-Сен-03 (1)Я не пойму, это вопрос из серии догадайтесь почему? Если нет, тогда где конфиги и s int
- SHDSL, Bobr, 16:24 , 20-Сен-03 (4)
>Я не пойму, это вопрос из серии догадайтесь почему? Если нет, тогда
>где конфиги и s int Первая 1 ip subnet-zero
!
!
!
!
interface ATM0
ip address 192.168.47.1 255.255.255.252
ip rip send version 2
ip rip receive version 2
no atm ilmi-keepalive
dsl equipment-type CO
dsl operating-mode GSHDSL symmetric annex A
dsl linerate AUTO
!
interface FastEthernet0
ip address 192.168.34.73 255.255.255.0
ip rip send version 2
ip rip receive version 2
speed auto
!
router rip
version 2
network 192.168.34.0
network 192.168.47.0
!
ip classless
no ip http server
!
!
!
line con 0
line aux 0
line vty 0 4
password open
login
!
no scheduler allocate
end
----------------------------------------------------------
Globespan G.SHDSL/SDSL Chipset Information Equipment Type: Central Office
Operating Mode: G.SHDSL Annex A
Clock Rate Mode: Auto rate selection Mode
Reset Count: 2
Actual rate: 2312 Kbps
Modem Status: Data (0x1)
Received SNR: 38 dB
SNR Threshold: 23 dB
Loop Attenuation: -0.6620 dB
Transmit Power: 7.5 dBm
Receiver Gain: 3.7580 dB
Last Activation Status: No Failure (0x0)
CRC Errors: 2
Chipset Version: 1
Firmware Version: R1.5 ^Yt^D Farend Statistics since CO boot-time: CRC Errors: 0
Errored Seconds: 0
Severly ES: 0
Un Available S: 0
Loss Of Sync S: 0 =========================================================
Вторая
ip subnet-zero
!
!
!
!
interface ATM0
ip address 192.168.47.2 255.255.255.252
ip rip send version 2
ip rip receive version 2
no atm ilmi-keepalive
dsl equipment-type CPE
dsl operating-mode GSHDSL symmetric annex A
dsl linerate AUTO
!
interface FastEthernet0
ip address 192.168.34.73 255.255.255.0
ip rip send version 2
ip rip receive version 2
speed auto
!
router rip
version 2
network 192.168.34.0
network 192.168.47.0
!
ip classless
no ip http server
!
!
!
line con 0
line aux 0
line vty 0 4
password open
login
!
no scheduler allocate
end
----------------------------------------------------------
Globespan G.SHDSL/SDSL Chipset Information
Equipment Type: Customer Premise
Operating Mode: G.SHDSL Annex A
Clock Rate Mode: Auto rate selection Mode
Reset Count: 2
Actual rate: 2312 Kbps
Modem Status: Data (0x1)
Received SNR: 38 dB
SNR Threshold: 23 dB
Loop Attenuation: -0.6620 dB
Transmit Power: 7.5 dBm
Receiver Gain: 3.7580 dB
Last Activation Status: No Failure (0x0)
CRC Errors: 2
Chipset Version: 1
Firmware Version: R1.5 ^Yt^D Farend Statistics since CO boot-time: CRC Errors: 0
Errored Seconds: 0
Severly ES: 0
Un Available S: 0
Loss Of Sync S: 0
- SHDSL, Bobr, 16:27 , 20-Сен-03 (5)
Поправка во втором конфиге interface FastEthernet0
ip address 192.168.34.73 255.255.255.0
ip rip send version 2
ip rip receive version 2
speed auto
192.168.34.73 255.255.255.0 читать как 192.168.47.5 255.255.255.252
- SHDSL, Bobr, 16:48 , 20-Сен-03 (6)
Ещё в догонку
router1#sh int atm 0
ATM0 is up, line protocol is up
Hardware is DSLSAR (with Globespan G.SHDSL module)
Internet address is 192.168.47.1/30
MTU 4470 bytes, sub MTU 4470, BW 2304 Kbit, DLY 880 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, no loopback
Encapsulation(s): AAL5 , PVC mode
23 maximum active VCs, 256 VCs per VP, 0 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: None
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 8 interface resets
0 output buffer failures, 0 output buffers swapped out
=========================
router2#sh int atm 0
ATM0 is up, line protocol is up
Hardware is DSLSAR (with Globespan G.SHDSL module)
Internet address is 192.168.47.2/30
MTU 4470 bytes, sub MTU 4470, BW 2304 Kbit, DLY 880 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, no loopback
Encapsulation(s): AAL5 , PVC mode
23 maximum active VCs, 256 VCs per VP, 0 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: None
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 8 interface resets
0 output buffer failures, 0 output buffers swapped out
- SHDSL, ВОЛКА, 18:19 , 20-Сен-03 (7)
а pvc кто прописывать за вас будет???
!
interface ATM0/0
ip address 192.1.9.254 255.255.255.0
no atm ilmi-keepalive
pvc 0/109
protocol ip 192.1.9.254
protocol ip 192.1.9.6 broadcast
no protocol ip inarp
!
dsl equipment-type CO
dsl operating-mode GSHDSL symmetric annex A
dsl linerate AUTO
!
- SHDSL, Bobr, 06:01 , 22-Сен-03 (8)
И так тоже пробовал :) всё равно не работат :(
- SHDSL, Misak Khachatryan, 09:35 , 23-Сен-03 (11)
У меня на Cisco 6160 работает такого типа конфигурацияinterface ATM0/0
ip address 192.1.9.254 255.255.255.0
no atm ilmi-keepalive
atm route-bridged ip
pvc 0/109
protocol ip 192.1.9.254
protocol ip 192.1.9.6 broadcast
no protocol ip inarp
encapsulation aal5snap --
Best regards,
Misak mailto:misak@xter.net
- SHDSL, Bobr, 10:33 , 23-Сен-03 (12)
>У меня на Cisco 6160 работает такого типа конфигурация
>
>interface ATM0/0
>ip address 192.1.9.254 255.255.255.0
>no atm ilmi-keepalive
>atm route-bridged ip
>pvc 0/109
> protocol ip 192.1.9.254
> protocol ip 192.1.9.6 broadcast
> no protocol ip inarp
> encapsulation aal5snap
>
>--
>Best regards,
> Misak
>
> mailto:misak@xter.net АААААА заработало :)
Всем спасибо :)
- SHDSL, ВОЛКА, 15:55 , 20-Сен-03 (2)
на одной стороне должно стоять CO
на другой CPE если back-to-back соединяете...
и после того как поменяли тип, интерфейсу сказать sh - no sh
- SHDSL, Bobr, 16:02 , 20-Сен-03 (3)
>на одной стороне должно стоять CO
>на другой CPE если back-to-back соединяете...
>и после того как поменяли тип, интерфейсу сказать sh - no sh
>Ну еслиб стояло на обоих CPE или СО то они вообщеб не соединялись :)
Я вот и говорю каналы поднимаются типа грит всё окей а работа не идёт :)
|
Версия для распечатки
SHDSL, 
