The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 [Cписок руководств | Печать]

pwd_mkdb ()
  • >> pwd_mkdb (8) ( FreeBSD man: Команды системного администрирования )

  • BSD mandoc


     - generate the password databases


    [-BCiLNp [-d directory ] ] [-s cachesize ] [-u username ] file  


    The utility creates db(3) style secure and insecure databases for the specified file. These databases are then installed into /etc/spwd.db and /etc/pwd.db respectively. The file is installed into /etc/master.passwd The file must be in the correct format (see passwd(5)). It is important to note that the format used in this system is different from the historic Version 7 style format.

    The options are as follows:

    Store data in big-endian format.
    Check if the password file is in the correct format. Do not change, add, or remove any files.
    Store data in little-endian format.
    Tell to exit with an error if it cannot obtain a lock on the file. By default, we block waiting for a lock on the source file. The lock is held through the rebuilding of the database.
    Create a Version 7 style password file and install it into /etc/passwd
    Ignore locking failure of the master.passwd file. This option is intended to be used to build password files in the release process over NFS where no contention can happen. A non-default directory must also be specified with the -d option for locking to be ignored. Other use of this option is strongly discouraged.
    -d directory
    Store databases into specified destination directory instead of /etc
    -u username
    Only update the record for the specified user. Utilities that operate on a single user can use this option to avoid the overhead of rebuilding the entire database.
    -s cachesize
    Specify in megabytes the size of the memory cache used by the hashing library. On systems with a large user base, a small cache size can lead to prohibitively long database file rebuild times. As a rough guide, the memory usage of in megabytes will be a little bit more than twice the figure specified here. The default is 2 megabytes.

    The two databases differ in that the secure version contains the user's encrypted password and the insecure version has an asterisk (``*'')

    The databases are used by the C library password routines (see getpwent(3)).

    The utility exits zero on success, non-zero on failure.  


    If the PW_SCAN_BIG_IDS environment variable is set, will suppress the warning messages that are normally generated for large user and group IDs. Such IDs can cause serious problems with software that makes assumptions about the values of IDs.  


    The insecure password database file.
    A temporary file.
    The secure password database file.
    A temporary file.
    The current password file.
    A Version 7 format password file.



    Previous versions of the system had a program similar to , mkpasswd(8), which built dbm(3) style databases for the password file but depended on the calling programs to install them. The program was renamed in order that previous users of the program not be surprised by the changes in functionality.  


    chpass(1), passwd(1), db(3), getpwent(3), passwd(5), vipw(8)  


    Because of the necessity for atomic update of the password files, uses rename(2) to install them. This, however, requires that the file specified on the command line live on the same file system as the /etc directory.

    There are the obvious races with multiple people running on different password files at the same time. The front-ends to , chpass(1), passwd(1) and vipw(8), handle the locking necessary to avoid this problem.




    Поиск по тексту MAN-ов: 

    Inferno Solutions
    Hosting by

    Закладки на сайте
    Проследить за страницей
    Created 1996-2022 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру