[-R
[-H | -L | -P
]
]
[-f | i | n
]
[-alpv
]
source_file target_file
[-R
[-H | -L | -P
]
]
[-f | i | n
]
[-alpv
]
source_file ... target_directory
DESCRIPTION
In the first synopsis form, the
utility copies the contents of the
source_file
to the
target_file
In the second synopsis form,
the contents of each named
source_file
is copied to the destination
target_directory
The names of the files themselves are not changed.
If
detects an attempt to copy a file to itself, the copy will fail.
The following options are available:
-H
If the
-R
option is specified, symbolic links on the command line are followed.
(Symbolic links encountered in the tree traversal are not followed.)
-L
If the
-R
option is specified, all symbolic links are followed.
-P
If the
-R
option is specified, no symbolic links are followed.
This is the default.
-R
If
source_file
designates a directory,
copies the directory and the entire subtree connected at that point.
If the
source_file
ends in a
/
the contents of the directory are copied rather than the
directory itself.
This option also causes symbolic links to be copied, rather than
indirected through, and for
to create special files rather than copying them as normal files.
Created directories have the same mode as the corresponding source
directory, unmodified by the process' umask.
Note that
copies hard linked files as separate files.
If you need to preserve hard links, consider using
tar(1),
cpio(1),
or
pax(1)
instead.
-a
Archive mode.
Same as
-RpP
-f
For each existing destination pathname, remove it and
create a new file, without prompting for confirmation
regardless of its permissions.
(The
-f
option overrides any previous
-i
or
-n
options.)
-i
Cause
to write a prompt to the standard error output before copying a file
that would overwrite an existing file.
If the response from the standard input begins with the character
`y
'
or
`Y
'
the file copy is attempted.
(The
-i
option overrides any previous
-f
or
-n
options.)
-l
Create hard links to regular files in a hierarchy instead of copying.
-n
Do not overwrite an existing file.
(The
-n
option overrides any previous
-f
or
-i
options.)
-p
Cause
to preserve the following attributes of each source
file in the copy: modification time, access time,
file flags, file mode, user ID, and group ID, as allowed by permissions.
If the user ID and group ID cannot be preserved, no error message
is displayed and the exit value is not altered.
If the source file has its set-user-ID bit on and the user ID cannot
be preserved, the set-user-ID bit is not preserved
in the copy's permissions.
If the source file has its set-group-ID bit on and the group ID cannot
be preserved, the set-group-ID bit is not preserved
in the copy's permissions.
If the source file has both its set-user-ID and set-group-ID bits on,
and either the user ID or group ID cannot be preserved, neither
the set-user-ID nor set-group-ID bits are preserved in the copy's
permissions.
-v
Cause
to be verbose, showing files as they are copied.
For each destination file that already exists, its contents are
overwritten if permissions allow.
Its mode, user ID, and group
ID are unchanged unless the
-p
option was specified.
In the second synopsis form,
target_directory
must exist unless there is only one named
source_file
which is a directory and the
-R
flag is specified.
If the destination file does not exist, the mode of the source file is
used as modified by the file mode creation mask
( umask
see
csh(1)).
If the source file has its set-user-ID bit on, that bit is removed
unless both the source file and the destination file are owned by the
same user.
If the source file has its set-group-ID bit on, that bit is removed
unless both the source file and the destination file are in the same
group and the user is a member of that group.
If both the set-user-ID and set-group-ID bits are set, all of the above
conditions must be fulfilled or both bits are removed.
Appropriate permissions are required for file creation or overwriting.
Symbolic links are always followed unless the
-R
flag is set, in which case symbolic links are not followed, by default.
The
-H
or
-L
flags (in conjunction with the
-R
flag) cause symbolic links to be followed as described above.
The
-H
-L
and
-P
options are ignored unless the
-R
option is specified.
In addition, these options override each other and the
command's actions are determined by the last one specified.
If
receives a
SIGINFO
(see the
status
argument for
stty(1))
signal, the current input and output file and the percentage complete
will be written to the standard output.
EXIT STATUS
Ex -std
COMPATIBILITY
Historic versions of the
utility had a
-r
option.
This implementation supports that option, however, its behavior
is different from historical
Fx behavior.
Use of this option
is strongly discouraged as the behavior is
implementation-dependent.
In
Fx ,
-r
is a synonym for
-RL
and works the same unless modified by other flags.
Historical implementations
of
-r
differ as they copy special files as normal
files while recreating a hierarchy.
The
-v
and
-n
options are non-standard and their use in scripts is not recommended.
