Интерактивная система просмотра системных руководств (man-ов)
xinetd (8)
xinetd (8) ( Русские man: Команды системного администрирования )
>> xinetd (8) ( Linux man: Команды системного администрирования )
NAME
xinetd - the extended Internet services daemon
SYNOPSIS
xinetd
[options]
DESCRIPTION
xinetd performs the same function as inetd: it starts
programs that provide Internet services. Instead of having such
servers started at system initialization time, and be dormant until a
connection request arrives, xinetd is the only daemon process
started and it listens on all service ports for the services listed in
its configuration file. When a request comes in, xinetd starts
the appropriate server. Because of the way it operates, xinetd
(as well as inetd) is also referred to as a super-server.
The services listed in xinetd's configuration file can be
separated into two groups. Services in the first group are called
multi-threaded
and they require the forking of a new server process for each new
connection request. The new server then handles that connection. For
such services, xinetd keeps listening for new requests so that it
can spawn new servers. On the other hand, the second group includes
services for which the service daemon is responsible for handling all
new connection requests. Such services are called
single-threaded
and xinetd will stop handling new requests for them until the
server dies. Services in this group are usually datagram-based.
So far, the only reason for the existence of a super-server was to
conserve system resources by avoiding to fork a lot of processes which
might be dormant for most of their lifetime. While fulfilling this
function, xinetd takes advantage of the idea of a super-server to
provide features such as access control and logging. Furthermore,
xinetd is not limited to services listed in
/etc/services.
Therefore, anybody can use xinetd to start special-purpose
servers.
OPTIONS
-d
Enables debug mode. This produces a lot of debugging output, and it
makes it possible to use a debugger on xinetd.
-syslog syslog_facility
This option enables syslog logging of xinetd-produced messages
using the specified syslog facility.
The following facility names are supported:
daemon,auth,user,local[0-7]
(check syslog.conf(5) for their meanings).
This option is ineffective in debug mode since all relevant messages are sent
to the terminal.
-filelog logfile
xinetd-produced messages will be placed in the specified file.
Messages are always appended to the file.
If the file does not exist, it will be created.
This option is ineffective in debug mode since all relevant messages are sent
to the terminal.
-f config_file
Determines the file that xinetd uses for configuration. The
default is /etc/xinetd.conf.
-pidfile pid_file
The process ID is written to the file. This option is ineffective in debug mode.
-dontfork
Tells xinetd to stay in the foreground rather than detaching itself, to
support being run from init or daemontools. This option automatically sets
-stayalive
(see below).
-stayalive
Tells xinetd to stay running even if no services are specified.
-limit proc_limit
This option places a limit on the number of concurrently running processes
that can be started by
xinetd.
Its purpose is to prevent process table overflows.
-logprocs limit
This option places a limit on the number of concurrently running servers
for remote userid acquisition.
-version
This option causes xinetd to print out its version information.
-inetd_compat
This option causes xinetd to read /etc/inetd.conf in addition to the
standard xinetd config files. /etc/inetd.conf is read after the
standard xinetd config files.
-cc interval
This option instructs
xinetd
to perform periodic consistency checks on its internal state every
interval
seconds.
The syslog and filelog options are mutually exclusive.
If none is specified, the default is syslog using the
daemon
facility.
You should not confuse xinetd messages with messages related to
service logging. The latter are logged only if this is specified
via the configuration file.
CONTROLLING XINETD
xinetd performs certain actions when it receives certain signals.
The actions associated with the specific signals can be redefined
by editing config.h and recompiling.
SIGHUP
causes a hard reconfiguration, which means that xinetd re-reads
the configuration file and terminates the servers for services that
are no longer available. Access control is performed again on
running servers by checking the remote location, access times and
server instances. If the number of server instances is lowered, some
arbitrarily picked servers will be killed to satisfy the limit; this
will happen after any servers are terminated because of failing
the remote location or access time checks.
Also, if the
INTERCEPT
flag was clear and is set, any running servers for that service will
be terminated;
the purpose of this is to ensure that after a hard reconfiguration
there will be no running servers that can accept packets from addresses
that do not meet the access control criteria.
SIGQUIT
causes program termination.
SIGTERM
terminates all running servers before terminating xinetd.
SIGUSR1
causes an internal state dump (the default dump file is
/var/run/xinetd.dump;
to change the filename, edit config.h and recompile).
SIGIOT
causes an internal consistency check to verify that the data structures
used by the program have not been corrupted.
When the check is completed
xinetd
will generate a message that says if the check was successful or not.
On reconfiguration the log files are closed and reopened. This allows
removal of old log files.
