[ новости /+++ | форум | теги | ]

NAME

Intro, intro - overview of device driver interfaces and introduction to driver entry points
 

DESCRIPTION

This page provides an overview of device driver interfaces and all of the Section 9 man pages (9E, 9F, 9P, and 9S). This overview is followed by an introduction to Section 9E, the driver entry-point routines.  

Overview of Device Driver Interfaces

Section 9 provides reference information needed to write device drivers for the Solaris operating environment. It describes the interfaces provided by the Device Driver Interface and the Driver-Kernel Interface (DDI/DKI).  

Porting

Software is usually considered portable if it can be adapted to run in a different environment more cheaply than it can be rewritten. The new environment may include a different processor, operating system, and even the language in which the program is written, if a language translator is available. Likewise the new environment might include multiple processors. More often, however, software is ported between environments that share an operating system, processor, and source language. The source code is modified to accommodate the differences in compilers or processors or releases of the operating system.

In the past, device drivers did not port easily for one or more of the following reasons:

o To enhance functionality, members had been added to kernel data structures accessed by drivers, or the sizes of existing members had been redefined.

o The calling or return syntax of kernel functions had changed.

o Driver developers did not use existing kernel functions where available, or relied on undocumented side effects that were not maintained in the next release.

o Architecture-specific code had been scattered throughout the driver when it could have been isolated.

Operating systems are periodically reissued to customers as a way to improve performance, fix bugs, and add new features. This is probably the most common threat to compatibility encountered by developers responsible for maintaining software. Another common problem is upgrading hardware. As new hardware is developed, customers occasionally decide to upgrade to faster, more capable computers of the same family. Although they may run the same operating system as those being replaced, architecture-specific code may prevent the software from porting.  

Scope of Interfaces

Although application programs have all of the porting problems mentioned, developers attempting to port device drivers have special challenges. Before describing the DDI/DKI, it is necessary to understand the position of device drivers in operating systems.

Device drivers are kernel modules that control data transferred to and received from peripheral devices but are developed independently from the rest of the kernel. If the goal of achieving complete freedom in modifying the kernel is to be reconciled with the goal of binary compatibility with existing drivers, the interaction between drivers and the kernel must be rigorously regulated. This driver/kernel service interface is the most important of the three distinguishable interfaces for a driver, summarized as follows:

o Driver-Kernel. I/O System calls result in calls to driver entry point routines. These make up the kernel-to-driver part of the service interface, described in Section 9E. Drivers may call any of the functions described in Section 9F. These are the driver-to-kernel part of the interface.

o Driver-Hardware. All drivers (except software drivers) must include code for interrupt handling, and may also perform direct memory access (DMA). These and other hardware-specific interactions make up the driver/hardware interface.

o Driver-Boot/Configuration Software. The interaction between the driver and the boot and configuration software is the third interface affecting drivers.

Scope of the DDI/DKI

The primary goal of the DDI/DKI is to facilitate both source and binary portability across successive releases of the operating systems on a particular machine. In addition, it promotes source portability across implementations of UNIX on different machines, and applies only to implementations based on System V Release 4. The DDI/DKI consists of several sections:

o DDI/DKI Architecture Independent - These interfaces are supported on all implementations of System V Release 4.

o DKI-only - These interfaces are part of System V Release 4, and may not be supported in future releases of System V. There are only two interfaces in this class, segmap(9E) and hat_getkpfnum(9F)

o Solaris DDI - These interfaces specific to Solaris.

o Solaris SPARC specific DDI - These interfaces are specific to the SPARC processor, and may not be available on other processors supported by Solaris.

o Solaris x86 specific DDI - These interfaces are specific to the x86 processor, and may not be available on other processors supported by Solaris.

To achieve the goal of source and binary compatibility, the functions, routines, and structures specified in the DDI/DKI must be used according to these rules.

o Drivers cannot access system state structures (for example, u and sysinfo) directly.

o For structures external to the driver that may be accessed directly, only the utility functions provided in Section 9F should be used. More generally, these functions should be used wherever possible.

o The headers <sys/ddi.h> and <sys/sunddi.h> must be the last header files included by the driver.

Audience

Section 9 is for software engineers responsible for creating, modifying, or maintaining drivers that run on this operating system and beyond. It assumes that the reader is familiar with system internals and the C programming language.  

PCMCIA Standard

The PC Card 95 Standard is listed under the SEE ALSO heading in some Section 9 reference pages. This refers to documentation published by the Personal Computer Memory Card International Association (PCMCIA) and the Japan Electronic Industry Development Association (JEIDA).  

How to Use Section 9

Section 9 is divided into the following subsections:

9E

Driver Entry Points - contains reference pages for all driver entry point routines.

9F

Kernel Functions - contains reference pages for all driver support routines.

9P

Driver Properties - contains reference pages for driver properties.

9S

Data Structures - contains reference pages for driver-related structures.

Compatibility Note

Sun Microsystem's implementation of the DDI/DKI was designed to provide binary compatibility for third-party device drivers across currently supported hardware platforms across minor releases of the operating system. However, unforeseen technical issues may force changes to the binary interface of the DDI/DKI. We cannot therefore promise or in any way assure that DDI/DKI-compliant device drivers will continue to operate correctly on future releases.  

Introduction to Section 9E

Section 9E describes the entry-point routines a developer can include in a device driver. These are called entry-point because they provide the calling and return syntax from the kernel into the driver. Entry-points are called, for instance, in response to system calls, when the driver is loaded, or in response to STREAMS events.

Kernel functions usable by the driver are described in section 9F.

In this section, reference pages contain the following headings:

o NAME describes the routine's purpose.

o SYNOPSIS summarizes the routine's calling and return syntax.

o INTERFACE LEVEL describes any architecture dependencies. It also indicates whether the use of the entry point is required, optional, or discouraged.

o ARGUMENTS describes each of the routine's arguments.

o DESCRIPTION provides general information about the routine.

o RETURN VALUES describes each of the routine's return values.

o SEE ALSO gives sources for further information.

Overview of Driver Entry-Point Routines and Naming Conventions

By convention, a prefix string is added to the driver routine names. For a driver with the prefix prefix, the driver code may contain routines named prefixopen, prefixclose, prefixread, prefixwrite, and so forth. All global variables associated with the driver should also use the same prefix.

All routines and data should be declared as static.

Every driver MUST include <sys/ddi.h> and <sys/sunddi.h>, in that order, and after all other include files.

The following table summarizes the STREAMS driver entry points described in this section.

Routine	Type
put	DDI/DKI
srv

The following table summarizes the driver entry points described in this section.

Routine	Type
_fini	Solaris DDI
_info
_init
aread
attach
awrite
chpoll
close
detach
devmap
devmap_access
devmap_contextmgt
devmap_dup
devmap_map
devmap_unmap
dump
getinfo
identify
ioctl
ks_update
mapdev_access
mapdev_dup
mapdev_free
mmap
open
power
print
probe
prop_op
read
segmap
strategy
tran_abort
tran_destroy_pkt
tran_dmafree
tran_getcap
tran_init_pkt
tran_reset
tran_reset_notify
tran_setcap
tran_start
tran_sync_pkt
tran_tgt_free
tran_tgt_init
tran_tgt_probe
write

The following table lists the error codes returned by a driver routine when it encounters an error. The error values are listed in alphabetic order and are defined in sys/errno.h. In the driver open(9E), close(9E), ioctl(9E), read(9E), and write(9E) routines, errors are passed back to the user by calling bioerror(9F) to set b_flags to the proper error code. In the driver strategy(9E) routine, errors are passed back to the user by setting the b_error member of the buf(9S) structure to the error code. For STREAMS ioctl routines, errors should be sent upstream in an M_IOCNAK message. For STREAMS read() and write() routines, errors should be sent upstream in an M_ERROR message. The driver print routine should not return an error code because the function that it calls, cmn_err(9F), is declared as void (no error is returned).

Error Value	Error Description
EAGAIN	Kernel resources, such as the buf structure or cache memory, are not available at this time (device may be busy, or the system resource is not available). This is used in open, ioctl, read, write, and strategy.
EFAULT
EINTR
EINVAL
EIO
ENXIO
EPERM
EROFS

The table below cross references error values to the driver routines from which the error values can be returned.

open close ioctl read, write and strategy EAGAIN EFAULT EAGAIN EAGAIN EFAULT EINTR EINVAL EIO ENXIO EPERM EROFS

SEE ALSO

Intro(9F), Intro(9S)

Index

NAME

DESCRIPTION

Overview of Device Driver Interfaces

Porting

Scope of Interfaces

Scope of the DDI/DKI

Audience

PCMCIA Standard

How to Use Section 9

Compatibility Note

Introduction to Section 9E

Overview of Driver Entry-Point Routines and Naming Conventions

SEE ALSO

Партнёры:

Хостинг: