The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

rtls (7)
  • >> rtls (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    rtls - Realtek Fast Ethernet 8139-based network interface controllers
     
    

    SYNOPSIS

    /dev/rtls 
    
     

    DESCRIPTION

    The rtls Ethernet driver is a multi-threaded, loadable, clonable, STREAMS hardware driver supporting the connectionless Data Link Provider Interface, dlpi(7P), over Realtek 8139 controllers. The rtls driver provides basic support for the Realtek 8139 hardware. Functions include chip initialization, frame transmit and receive, multicast support, and error recovery and reporting.  

    APPLICATION PROGRAMMING INTERFACE

    The cloning, character-special device /dev/rtls is used to access all 8139 devices installed within the system.  

    rtls and DLPI

    The rtls driver is dependent on /kernel/misc/gld, a loadable kernel module that provides the rtls driver with the DLPI and STREAMS functionality required of a LAN driver. See gld(7D) for more details on the primitives supported by the driver.

    The values returned by the driver in the DL_INFO_ACK primitive in response to the DL_INFO_REQ from the user are as follows:

    * Maximum SDU is 1500 (ETHERMTU).

    * Minimum SDU is 0. The driver pads to the mandatory 60-octet minimum packet size.

    * The dlsap address length is 8.

    * MAC type is DL_ETHER.

    * The sap length value is -2, meaning the physical address component is followed immediately by a 2-byte sap component within the DLSAP address.

    * Broadcast address value is Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF).

     

    KNOWN PROBLEMS AND LIMITATIONS

    The rtls driver only supports Realtek 8139 on x86 platforms.

    The rtls driver does not support the NDD interface and MII statistics. Realtek 8139 works under 100FDX/100HDX and 10FDX/10HDX modes, which you can set using the rtls.conf file.  

    CONFIGURATION

    To configure the rtls driver:

    * Use prtconf -v | grep pci10ec,8139 to obtain the instance number of the driver. (pci1186,1301 or pci1113,1211 indicates a third-party ethernet device with an 8139 chip that can also be controlled by the rtls driver.)

    The rtls.conf configuration file options include:

    -ForceSpeedDuplex

    Default: 5 (Auto-negotiate)

    Allowed Values:        4 (100 FDX)

    3 (100 HDX)

    2 (10 FDX)

    1 (10 HDX)

    Specify the speed and duplex mode for each instance.

    Example: ForceSpeedDuplex=5,4;

    Sets rtls0 to autonegotiate and rtls1 to 100 FDX.

     

    FILES

    rtls

    Device special file.

    /kernel/drv/rtls.conf

    rtls configuration file.

    <sys/stropts.h>

    stropts network header file.

    <sys/ethernet.h>

    Ethernet network header file.

    <sys/dlpi.h>

    dlpi network header file.

    <sys/gld.h>

    gld network header file.

     

    ATTRIBUTES

    See attributes(5) for descriptions of the following attributes:

    ATTRIBUTE TYPEATTRIBUTE VALUE
    Architecturex86

     

    SEE ALSO

    attributes(5), dlpi(7P), gld(7D)


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    APPLICATION PROGRAMMING INTERFACE
    rtls and DLPI
    KNOWN PROBLEMS AND LIMITATIONS
    CONFIGURATION
    FILES
    ATTRIBUTES
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру