The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

sysidcfg (4)
  • >> sysidcfg (4) ( Solaris man: Специальные файлы /dev/* )
  •  

    NAME

    sysidcfg - system identification configuration file
     
    

    DESCRIPTION

    When a diskless client boots for the first time or a system installs over the network, the booting software tries to obtain configuration information about the system, such as the system's root password or name service, from, first, a sysidcfg file and then the name service databases. If the booting software cannot find the information, it prompts the user for it. Like the name service databases, the sysidcfg file can be used to avoid the user prompts and provide a totally hands-off booting process.

    The sysidcfg file preconfigures information through a set of keywords. You can specify one or more of the keywords to preconfigure as much information as you want. Each set of systems (one or more) that has unique configuration information must have its own sysidcfg file. For example, you can use the same sysidcfg file to preconfigure the time zone for multiple systems if you want all the systems to have the same time zone configured. However, if you want to preconfigure a different root password for each of those systems, then each system would need its own sysidcfg file.

    If a syntax error (such as an invalid keyword) is detected when reading the sysidcfg file, an error message that notes the position in the file where the error was found is sent to the console. Under such a condition, the file is not used.  

    Where To Put the sysidcfg File

    The sysidcfg file can reside on a shared NFS network directory or the root directory on a UFS or PCFS diskette in the system's diskette drive. If you put the sysidcfg file on a shared NFS network directory, you have to use the -p option of the add_install_client(1M) command (see install_scripts(1M)) to specify where the system being installed can find the sysidcfg file. If you put the sysidcfg file on a diskette, you need to make sure the diskette is in the system's diskette drive when the system boots (on x86 systems, the sysidcfg file should reside on the Solaris Device Configuration Assistant diskette).

    Only one sysidcfg file can reside in a directory or diskette. If you are creating more than one sysidcfg file, they must reside in different directories or diskettes.  

    Keyword Syntax Rules

    The following rules apply to the keywords in a sysidcfg file:

    o Keywords can be in any order
    o Keywords are not case-sensitive
    o Keyword values can be optionally enclosed in single (') or double (") quotes
    o Only the first instance of a keyword is valid; if you specify the same keyword more than once, the first keyword specified is used. The network_interface keyword is exempt from this rule.
     

    Keywords - All Platforms

    The following keywords apply to both SPARC and x86 platforms.  

    Name Service, Domain Name, Name Server

    Naming-related keywords are as follows:

    name_service=NIS,NIS+,LDAP,DNS,NONE
    

    For the NIS and NIS+ keywords, the options are:

    domain_name=domain_name
    name_server=hostname(ip_address)
    

    The following is an example NIS entry:

    name_service=NIS 
    {domain_name=west.arp.com name_server=timber(172.16.2.1)}
    

    For NIS+, the example is identical to the one above, except for the replacement of the keyword NIS by NIS+.

    For DNS, the syntax is:

    domain_name=domain_name; name_server=ip_address, ... ; 
    search=domain_name, ...
    

    You can have a maximum of three IP addresses and six domain names. The total length of a search entry cannot exceed 250 characters. The following is an example DNS entry:

    name_service=DNS
    {domain_name=west.arp.com
    name_server=10.0.1.10,10.0.1.20
    search=arp.com,east.arp.com}
    

    For LDAP, the syntax is:

    domain_name=domain_name;
    profile=profile_name;
    profile_server=ip_address;
    proxy_dn="proxy_bind_dn";
    proxy_password=password 
    

    The proxy_dn and proxy_password keywords are optional. If proxy_dn is used, the value must be enclosed in double quotes.

    The following is an example LDAP entry:

    name_service=LDAP
    {domain_name=west.arp.com
    profile=default
    profile_server=172.16.2.1
    proxy_dn="cn=proxyagent,ou=profile,dc=west,dc=arp,dc=com"
    proxy_password=password}
    

    Choose only one value for name_service. Include either, both, or neither of the domain_name and name_server keywords, as needed. If no keywords are used, omit the curly braces.  

    NFS version 4 Default Domain Name

    There is only one keyword for specifying the NFSv4 default domain name:

    nfs4_domain=dynamic, value
    

    where value must be a fully qualified domain name, as per RFC1033 and RFC1035 recommendations. The reserved value dynamic suppresses the front-end installation prompt. At the same time, use of dynamic enables the NFSv4 domain to be derived dynamically, at run time, based on naming service configuration.

    For example:

    nfs4_domain=example.com
    

    ...hard codes the value used by the nfsmapid(1M) daemon to be example.com. In contrast, the following example shows how to set the nfs4_domain variable to the reserved keyword dynamic:

    nfs4_domain=dynamic
    

    The preceding example enables the nfsmapid(1M) daemon to derive the domain from the system's configured naming services, as prescribed in the System Administration Guide: Network Services.  

    Network Interface, Hostname, IP address, Netmask, DHCP, Default Route

    Network-related keywords are as follows:

    network_interface=NONE, PRIMARY, value
    

    where value is a name of a network interface, for example, eri0 or hme0.

    For the NONE keyword, the options are:

    hostname=hostname
    

    For example,

    network_interface=NONE {hostname=feron}
    

    For the PRIMARY and value keywords, the options are:

    primary (used only with multiple network_interface lines)
    dhcp
    hostname=hostname
    ip_address=ip_address
    netmask=netmask
    protocol_ipv6=yes | no
    default_route=ip_address (IPv4 address only)
    

    If you are using the dhcp option, the only other option you can specify is protocol_ipv6. For example:

    network_interface=PRIMARY {dhcp protocol_ipv6=yes}
    

    If you are not using DHCP, you can specify any combination of the other keywords as needed. If you do not use any of the keywords, omit the curly braces.

    network_interface=eri0 {hostname=feron
            ip_address=172.16.2.7
            netmask=255.255.255.0
            protocol_ipv6=no
            default_route=172.16.2.1}
    

     

    Multiple Network Interfaces

    If you have multiple network interfaces on your system, you can configure them all in the sysidcfg file by defining multiple network_interface keywords. If you specify multiple network_interface keywords, you cannot use NONE or PRIMARY for values. You must specify interface names for all of the values. To specify the primary interface, use the primary option value.

    For example,

    network_interface=eri0 {primary
            hostname=feron
            ip_address=172.16.2.7
            netmask=255.255.255.0
            protocol_ipv6=no
            default_route=172.16.2.1}
    
    network_interface=eri1 {hostname=feron-b
            ip_address=172.16.3.8
            netmask=255.255.255.0
            protocol_ipv6=no
            default_route=172.16.3.1}
    

     

    Root Password

    The root password keyword is root_password. Possible values are encrypted from /etc/shadow. Syntax is:

    root_password=encrypted_password
    

     

    Security Policy

    The security---related keyword is security_policy. It has the following syntax:

    security_policy=kerberos, NONE
    

    The kerberos keyword has the following options:

    {default_realm=FQDN admin_server=FQDN kdc=FQDN1, FQDN2, FQDN3}
    

    where FQDN is a fully qualified domain name. An example of the security_policy keyword is as follows:

    security_policy=kerberos {default_realm=Yoursite.COM
    admin_server=krbadmin.Yoursite.COM
    kdc=kdc1.Yoursite.COM, kdc2.Yoursite.COM}
    

    You can list a maximum of three key distribution centers (KDCs) for a security_policy keyword. At least one is required.  

    Language in Which to Display the Install Program

    The system-location keyword is system_locale. It has the following syntax:

    system_locale=locale
    

    where locale is /usr/lib/locale.  

    Terminal Type

    The terminal keyword is terminal. It has the following syntax:

    terminal=terminal_type
    

    where terminal_type is a value from /usr/share/lib/terminfo/*.  

    Timezone Information

    The timezone keyword is timezone. It has the following syntax:

    timezone=timezone
    

    where timezone is a value from /usr/share/lib/zoneinfo/*or, where timezone is an offset-from-GMT style quoted timezone. Refer to environ(5) for information on quoted timezones. An example of a quoted timezone is: timezone="<GMT+8>+8".  

    Date and Time

    The time server keyword is timeserver. It has the following syntax:

    timeserver=localhost
    timeserver=hostname
    timeserver=ip_address
    

    If you specify localhost as the time server, the system's time is assumed to be correct. If you specify the hostname or ip_address, if you are not running a name service, of a system, that system's time is used to set the time.  

    Keyboard Layout

    The keyboard keyword is keyboard. It has the following syntax:

    keyboard=keyboard_layout
    

    The valid keyboard_layout strings are defined in the /usr/share/lib/keytables/type_6/kbd_layouts file.  

    x86 Platform Keywords

    The following keywords apply only to x86 platforms. For all these keywords, use kdmconfig -d to create or append to the sysidcfg file. See kdmconfig(1M).

    Monitor type

    The monitor---related keyword is monitor. The syntax is:

    monitor=monitor_type
    

    Graphics card, color depth, display resolution, screen size

    The display-related keywords are display, size, depth, and resolution. The syntax is:

    display=graphics_card {size=screen_size
    depth=color_depth resolution=screen_resolution}
    

    Pointing device, number of buttons, IRQ level

    The mouse-related keywords are pointer, nbuttons, and irq.

    pointer=pointing_device {nbuttons=number_buttons
    irq=value}
    

     

    EXAMPLES

    Example 1 Sample sysidcfg files

    The following example is a sysidcfg file for a group of SPARC systems to install over the network. The host names, IP addresses, and netmask of these systems have been preconfigured by editing the name service. Because all the system configuration information has been preconfigured, an automated installation can be achieved by using this sysidcfg file in conjunction with a custom JumpStart profile.

    keyboard=US-English
    system_locale=en_US
    timezone=US/Central
    timeserver=localhost
    terminal=sun-cmd
    name_service=NIS {domain_name=marquee.central.example.com
                     name_server=connor(172.16.112.3)}
    root_password=m4QPOWNY
    system_locale=C
    security_policy=kerberos 
       {default_realm=Yoursite.COM 
        admin_server=krbadmin.Yoursite.COM
        kdc=kdc1.Yoursite.COM, kdc2.Yoursite.COM}
    

    The following example is a sysidcfg file created for a group of x86 systems to install over the network that all have the same keyboard, graphics cards, and pointing devices. The device information (keyboard, display, and pointer) was captured from running kdmconfig -d. See kdmconfig(1M). In this example, users would see only the prompt to select a language, system_locale, for displaying the rest of the Solaris installation program.

    keyboard=US-English
    display=ati {size=15-inch}
    pointer=MS-S
    timezone=US/Central
    timeserver=connor
    terminal=AT386
    name_service=NIS {domain_name=marquee.central.example.com
                     name_server=connor(172.16.112.3)}
    root_password=URFUni9
    security_policy=none
    

     

    SEE ALSO

    install_scripts(1M), kdmconfig(1M), nfsmapid(1M), sysidtool(1M), environ(5)

    Solaris Express Installation Guide: Basic Installations


     

    Index

    NAME
    DESCRIPTION
    Where To Put the sysidcfg File
    Keyword Syntax Rules
    Keywords - All Platforms
    Name Service, Domain Name, Name Server
    NFS version 4 Default Domain Name
    Network Interface, Hostname, IP address, Netmask, DHCP, Default Route
    Multiple Network Interfaces
    Root Password
    Security Policy
    Language in Which to Display the Install Program
    Terminal Type
    Timezone Information
    Date and Time
    Keyboard Layout
    x86 Platform Keywords
    EXAMPLES
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру