The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

форумы  помощь  поиск  регистрация  майллист  ВХОД  слежка  RSS
"lan-lan на базе zyxel 782R"
Вариант для распечатки Архивированная нить - только для чтения! 
Пред. тема | След. тема 
Форумы Маршрутизаторы CISCO и др. оборудование. (Public)
Изначальное сообщение [Проследить за развитием треда]

"lan-lan на базе zyxel 782R" 
Сообщение от maf_nik Найти другие сообщения данного автораПоместить сообщение в закладки. См. нижнее поле навигации.(ok) on 17-Июн-04, 15:50  (MSK)
собрана конфигурация на базе двух zyxel 782R lan-lan (конфиг прилагается), никакой IP траффик кроме ping'а между сетками 192.168.1.0 и 192.168.2.0 не проходит, подскажите пожалуйста в чём может быть проблема ?

server
  
    Menu 1 - General Setup
                    System Name= s1
                    Location= nik
                    Contact Person's Name= maf


                    Route IP= Yes
                    Route IPX= No
                    Bridge= No

    Menu 2 - WAN Setup
                    Service Type= Server
                    Rate Adaption= Enable
                    Transfer Max Rate(Kbps)= 2312K
                    Transfer Min Rate(Kbps)= 72K
                    Standard Mode= ETSI(ANNEX_B)

    Menu 3.2 - TCP/IP and DHCP Ethernet Setup
                    DHCP Setup
                      DHCP= Server
                      Client IP Pool Starting Address= 192.168.1.33
                      Size of Client IP Pool= 4
                      Primary DNS Server= 0.0.0.0
                      Secondary DNS Server= 0.0.0.0
                      Remote DHCP Server= N/A
                    TCP/IP Setup:
                      IP Address= 192.168.1.1
                      IP Subnet Mask= 255.255.255.0
                      RIP Direction= Both
                        Version= RIP-1
                      Multicast= None
                      IP Policies=
                      Edit IP Alias= No

    Menu 4 - Internet Access Setup
                    ISP's Name= c1
                    Encapsulation= RFC 1483
                    Multiplexing= LLC-based
                    VPI #= 0
                    VCI #= 38
                    Peak Cell Rate (cell/sec)= 20000
                    Sustain Cell Rate (cell/sec)= 0
                    Maximum Burst Size (cell)= 0
                    Service Name= N/A
                    My Login= N/A
                    My Password= N/A
                    Single User Account= No
                    IP Address Assignment= N/A
                      IP Address= N/A
                    ENET ENCAP Gateway= N/A

    Menu 11.1 - Remote Node Profile
     Rem Node Name= c1                    Route= IP
     Active= Yes                          Bridge= No

     Encapsulation= RFC 1483              Edit PPP Options= N/A
     Multiplexing= LLC-based              Rem IP Addr= 192.168.2.1
     Incoming:                            Edit IP/IPX/Bridge= No
       Rem Login= N/A                     Edit ATM Options= No
       Rem Password= N/A
     Outgoing:                            Session Options:
       My Login= N/A                        Edit Filter Sets= No
       My Password= N/A                     PPPoE Idle Timeout(sec)= N/A
       Authen= N/A                          PPPoE Service Name= N/A
    
    Menu 24.2.1 - System Maintenance - Information
                    Name: s1
                    Routing: IP
                    ZyNOS F/W Version: V2.50(BH.4) | 8/6/2002
                    xDSL F/W Version: R.1.5
                    Country Code: 255

                    LAN
                      Ethernet Address: 00:a0:c5:55:2f:13
                      IP Address: 192.168.1.1
                      IP Mask: 255.255.255.0
                      DHCP: Server

client  

   Menu 1 - General Setup

                    System Name= c1
                    Location= nik
                    Contact Person's Name= maf

                    Route IP= Yes
                    Route IPX= No
                    Bridge= No

   Menu 2 - WAN Setup
                    Service Type= Client
                    Rate Adaption= Enable
                    Transfer Max Rate(Kbps)= 2312K
                    Transfer Min Rate(Kbps)= 72K
                    Standard Mode= ETSI(ANNEX_B)

   Menu 3.2 - TCP/IP and DHCP Ethernet Setup
                    DHCP Setup
                      DHCP= None
                      Client IP Pool Starting Address= N/A
                      Size of Client IP Pool= N/A
                      Primary DNS Server= N/A
                      Secondary DNS Server= N/A
                      Remote DHCP Server= N/A
                    TCP/IP Setup:
                      IP Address= 192.168.2.1
                      IP Subnet Mask= 255.255.255.0
                      RIP Direction= Both
                        Version= RIP-1
                      Multicast= None
                      IP Policies=
                      Edit IP Alias= No
  
    Menu 4 - Internet Access Setup
                    ISP's Name= s1
                    Encapsulation= RFC 1483
                    Multiplexing= LLC-b
                    VPI #= 0
                    VCI #= 38
                    Peak Cell Rate (cell/sec)=
                    Sustain Cell Rate (cell/sec)=
                    Maximum Burst Size (cell)=
                    Service Name= N/A
                    My Login= N/A
                    My Password= N/A
                    Single User Account=
                    IP Address Assignment= N/A
                      IP Address= N/A
                    ENET ENCAP Gateway= N/A  
  
    Menu 11.1 - Remote Node Profile
     Rem Node Name= s1                    Route= IP
     Active= Yes                          Bridge= No

     Encapsulation= RFC 1483              Edit PPP Options= N/A
     Multiplexing= LLC-based              Rem IP Addr= 192.168.1.1
     Incoming:                            Edit IP/IPX/Bridge= No
       Rem Login= N/A                     Edit ATM Options= No
       Rem Password= N/A
     Outgoing:                            Session Options:
       My Login= N/A                        Edit Filter Sets= No
       My Password= N/A                     PPPoE Idle Timeout(sec)= N/A
       Authen= N/A                          PPPoE Service Name= N/A

      Menu 24.2.1 - System Maintenance - Information
                    Name: c1
                    Routing: IP
                    ZyNOS F/W Version: V2.50(BH.4) | 8/6/2002
                    xDSL F/W Version: R.1.5
                    Country Code: 255

                    LAN
                      Ethernet Address: 00:a0:c5:55:2f:14
                      IP Address: 192.168.2.1
                      IP Mask: 255.255.255.0
                      DHCP: None

  Рекомендовать в FAQ | Cообщить модератору | Наверх

 Оглавление

Индекс форумов | Темы | Пред. тема | След. тема
Сообщения по теме

1. "lan-lan на базе zyxel 782R" 
Сообщение от serga emailНайти другие сообщения данного автораПоместить сообщение в закладки. См. нижнее поле навигации. on 18-Июн-04, 06:29  (MSK)
>собрана конфигурация на базе двух zyxel 782R lan-lan (конфиг прилагается), никакой IP
>траффик кроме ping'а между сетками 192.168.1.0 и 192.168.2.0 не проходит, подскажите
>пожалуйста в чём может быть проблема ?
>
> server
>
>    Menu 1 - General Setup
>            
>        System Name= s1
>
>            
>        Location= nik
>            
>        Contact Person's Name=
>maf
>
>
>            
>        Route IP= Yes
>
>            
>        Route IPX= No
>
>            
>        Bridge= No
>
>    Menu 2 - WAN Setup
>            
>        Service Type= Server
>
>            
>        Rate Adaption= Enable
>
>            
>        Transfer Max Rate(Kbps)=
>2312K
>            
>        Transfer Min Rate(Kbps)=
>72K
>            
>        Standard Mode= ETSI(ANNEX_B)
>
>
>    Menu 3.2 - TCP/IP and DHCP Ethernet Setup
>
>            
>        DHCP Setup
>            
>          DHCP=
>Server
>            
>          Client
>IP Pool Starting Address= 192.168.1.33
>            
>          Size
>of Client IP Pool= 4
>            
>          Primary
>DNS Server= 0.0.0.0
>            
>          Secondary
>DNS Server= 0.0.0.0
>            
>          Remote
>DHCP Server= N/A
>            
>        TCP/IP Setup:
>            
>          IP
>Address= 192.168.1.1
>            
>          IP
>Subnet Mask= 255.255.255.0
>            
>          RIP
>Direction= Both
>            
>          
> Version= RIP-1
>            
>          Multicast=
>None
>            
>          IP
>Policies=
>            
>          Edit
>IP Alias= No
>
>    Menu 4 - Internet Access Setup
>            
>        ISP's Name= c1
>
>            
>        Encapsulation= RFC 1483
>
>            
>        Multiplexing= LLC-based
>            
>        VPI #= 0
>
>            
>        VCI #= 38
>
>            
>        Peak Cell Rate
>(cell/sec)= 20000
>            
>        Sustain Cell Rate
>(cell/sec)= 0
>            
>        Maximum Burst Size
>(cell)= 0
>            
>        Service Name= N/A
>
>            
>        My Login= N/A
>
>            
>        My Password= N/A
>
>            
>        Single User Account=
>No
>            
>        IP Address Assignment=
>N/A
>            
>          IP
>Address= N/A
>            
>        ENET ENCAP Gateway=
>N/A
>
>    Menu 11.1 - Remote Node Profile
>     Rem Node Name= c1    
>          
>     Route= IP
>     Active= Yes      
>          
>         Bridge= No
>
>
>     Encapsulation= RFC 1483    
>         Edit PPP
>Options= N/A
>     Multiplexing= LLC-based      
>        Rem IP Addr=
>192.168.2.1
>     Incoming:      
>          
>          Edit
>IP/IPX/Bridge= No
>       Rem Login= N/A  
>          
>       Edit ATM Options= No
>
>       Rem Password= N/A
>     Outgoing:      
>          
>          Session
>Options:
>       My Login= N/A  
>          
>          Edit
>Filter Sets= No
>       My Password= N/A  
>          
>       PPPoE Idle Timeout(sec)= N/A
>
>       Authen= N/A    
>          
>          
>PPPoE Service Name= N/A
>
>    Menu 24.2.1 - System Maintenance - Information
>            
>        Name: s1
>            
>        Routing: IP
>            
>        ZyNOS F/W Version:
>V2.50(BH.4) | 8/6/2002
>            
>        xDSL F/W Version:
>R.1.5
>            
>        Country Code: 255
>
>
>            
>        LAN
>            
>          Ethernet
>Address: 00:a0:c5:55:2f:13
>            
>          IP
>Address: 192.168.1.1
>            
>          IP
>Mask: 255.255.255.0
>            
>          DHCP:
>Server
>
> client
>
>   Menu 1 - General Setup
>
>            
>        System Name= c1
>
>            
>        Location= nik
>            
>        Contact Person's Name=
>maf
>
>            
>        Route IP= Yes
>
>            
>        Route IPX= No
>
>            
>        Bridge= No
>
>   Menu 2 - WAN Setup
>            
>        Service Type= Client
>
>            
>        Rate Adaption= Enable
>
>            
>        Transfer Max Rate(Kbps)=
>2312K
>            
>        Transfer Min Rate(Kbps)=
>72K
>            
>        Standard Mode= ETSI(ANNEX_B)
>
>
>   Menu 3.2 - TCP/IP and DHCP Ethernet Setup
>            
>        DHCP Setup
>            
>          DHCP=
>None
>            
>          Client
>IP Pool Starting Address= N/A
>            
>          Size
>of Client IP Pool= N/A
>            
>          Primary
>DNS Server= N/A
>            
>          Secondary
>DNS Server= N/A
>            
>          Remote
>DHCP Server= N/A
>            
>        TCP/IP Setup:
>            
>          IP
>Address= 192.168.2.1
>            
>          IP
>Subnet Mask= 255.255.255.0
>            
>          RIP
>Direction= Both
>            
>          
> Version= RIP-1
>            
>          Multicast=
>None
>            
>          IP
>Policies=
>            
>          Edit
>IP Alias= No
>
>    Menu 4 - Internet Access Setup
>            
>        ISP's Name= s1
>
>            
>        Encapsulation= RFC 1483
>
>            
>        Multiplexing= LLC-b
>            
>        VPI #= 0
>
>            
>        VCI #= 38
>
>            
>        Peak Cell Rate
>(cell/sec)=
>            
>        Sustain Cell Rate
>(cell/sec)=
>            
>        Maximum Burst Size
>(cell)=
>            
>        Service Name= N/A
>
>            
>        My Login= N/A
>
>            
>        My Password= N/A
>
>            
>        Single User Account=
>
>            
>        IP Address Assignment=
>N/A
>            
>          IP
>Address= N/A
>            
>        ENET ENCAP Gateway=
>N/A
>
>    Menu 11.1 - Remote Node Profile
>     Rem Node Name= s1    
>          
>     Route= IP
>     Active= Yes      
>          
>         Bridge= No
>
>
>     Encapsulation= RFC 1483    
>         Edit PPP
>Options= N/A
>     Multiplexing= LLC-based      
>        Rem IP Addr=
>192.168.1.1
>     Incoming:      
>          
>          Edit
>IP/IPX/Bridge= No
>       Rem Login= N/A  
>          
>       Edit ATM Options= No
>
>       Rem Password= N/A
>     Outgoing:      
>          
>          Session
>Options:
>       My Login= N/A  
>          
>          Edit
>Filter Sets= No
>       My Password= N/A  
>          
>       PPPoE Idle Timeout(sec)= N/A
>
>       Authen= N/A    
>          
>          
>PPPoE Service Name= N/A
>
>      Menu 24.2.1 - System Maintenance -
>Information
>            
>        Name: c1
>            
>        Routing: IP
>            
>        ZyNOS F/W Version:
>V2.50(BH.4) | 8/6/2002
>            
>        xDSL F/W Version:
>R.1.5
>            
>        Country Code: 255
>
>
>            
>        LAN
>            
>          Ethernet
>Address: 00:a0:c5:55:2f:14
>            
>          IP
>Address: 192.168.2.1
>            
>          IP
>Mask: 255.255.255.0
>            
>          DHCP:
>None
некоторым этого достаточно ...

  Рекомендовать в FAQ | Cообщить модератору | Наверх


Удалить

Индекс форумов | Темы | Пред. тема | След. тема
Пожалуйста, прежде чем написать сообщение, ознакомьтесь с данными рекомендациями.




Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру