форумы  помощь  поиск  регистрация  майллист  ВХОД  слежка

Вариант для распечатки		Пред. тема | След. тема
Форумы Маршрутизаторы CISCO и др. оборудование. (Public)
Изначальное сообщение		[Проследить за развитием треда]

"CISCO 170 + WIC 1ENET - проблемы"
Сообщение от LuckyBird (??) on 28-Июн-05, 11:05  (MSK)
Добпый день, установи я в cisco 170  плату WIC 1 ENET Как я понимаю сisco её не опознала: show version Cisco Internetwork Operating System Software IOS (tm) C1700 Software (C1700-Y-M), Version 12.1(10), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Mon 06-Aug-01 21:15 by kellythw Image text-base: 0x80008088, data-base: 0x805F5400 ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1) IntStep uptime is 2 days, 17 hours, 13 minutes System returned to ROM by power-on System image file is "flash:c1700-y-mz.121-10.bin" cisco 1720 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory . Processor board ID JAD0551061X (619516019), with hardware revision 0000 M860 processor: part number 0, mask 32 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 show diag 0 WIC Slot 1:         Unknown WAN daughter card         Hardware revision 64.0  Board revision G0         Serial number     0960561920    Part number    130-18710-165         Test history      0x03          RMA number     66-67-48         Connector type    PCI         EEPROM format version 4         EEPROM contents (hex):         0x20:   04 FF 40 00 39 41 03 00 82 49 16 A5 03 42 43 30         0x30:   80 00 00 00 00 02 02 C1 8B 46 4F 43 30 39 30 34 Подскажиет что делать :?
	Правка | Высказать мнение | Ответить | Рекомендовать в FAQ | Cообщить модератору | Наверх

Индекс форумов | Темы | Пред. тема | След. тема

Сообщения по теме

1. "CISCO 170 + WIC 1ENET - проблемы"
Сообщение от Сайко on 28-Июн-05, 13:20  (MSK)
Configuring a Single-Port Ethernet WIC on a Cisco 1700 Series Router http://www.cisco.com/en/US/products/hw/modules/ps2641/prod_module_installation_guide09186a008007cf93.html Software Requirements The Cisco WIC-1ENET card requires Cisco IOS Release 12.2(2)XJ or later if the card is installed in any WIC slot other than slot 0 or if more than one card is installed. The card can be used with Cisco IOS Release 12.2(4)T, but the card must be installed in slot 0 and only one Cisco WIC-1ENET card can be installed in the router. Caveats for All Cisco WIC-1ENET Cards This section provides the latest information about using a Cisco WIC-1ENET card when the router is running Cisco IOS Release 12.2(2)XJ or higher. •If the Cisco WIC-1ENET is used with an IOS image that does not support it and if the Link LED does not light, an error message appears, indicating an unrecognized WIC. This does not damage the router or the Cisco WIC-1ENET card. The error message is "00:00:05: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID of 0xFF." •The router cannot use TFTP over the Cisco WIC-1ENET Ethernet connection until the router completes the boot process. •This interface is not supported in the ROM Monitor; therefore, a TFTP download cannot be performed by using the interface in ROM Monitor mode. The 10/100 Ethernet interface supports TFTP download in ROM monitor mode. We suggest connecting the FE interface to the side of the network that provides the image. •If two Cisco WIC-1ENET cards are installed, the first detected card will be "interface Ethernet 0", regardless of the slot position. If one of the Cisco WIC-1ENET cards is later removed, be sure to remove the card from slot 1, so that the card in slot 0 will continue to be detected. Caveats for Cisco WIC-1ENET Cards in Routers Running Cisco IOS Release 12.2(4)T This section provides the latest information about using a Cisco WIC-1ENET card when the router is running Cisco IOS Release 12.2(4)T. •Only one Cisco WIC-1ENET can be installed in a Cisco 1720 or Cisco 1750 series router. •Inserting the Cisco WIC-1ENET into slot 1 or slot 2 does not damage the router or the Cisco WIC-1ENET. •The Cisco WIC-1ENET can be installed only in slot 0 of the Cisco 1720 or Cisco 1750 series router. If a Cisco WIC-1ENET is inserted in slot 1, an error message appears when the router is booted, and the interface is not available. The Link LED also does not light, because the IOS does not attempt any interaction when the Cisco WIC-1ENET is in an unsupported slot.
Удалить	Правка | Высказать мнение | Ответить | Рекомендовать в FAQ | Cообщить модератору | Наверх

2. "CISCO 170 + WIC 1ENET - проблемы"
Сообщение от toor99 (??) on 29-Июн-05, 12:33  (MSK)
Поставить IOS, который знает о существовании WIC-1ENET.
Удалить	Правка | Высказать мнение | Ответить | Рекомендовать в FAQ | Cообщить модератору | Наверх

Архив | Удалить	Индекс форумов | Темы | Пред. тема | След. тема
Оцените тред (1=ужас, 5=супер)? [ 1 | 2 | 3 | 4 | 5 ]

Пожалуйста, прежде чем написать сообщение, ознакомьтесь с данными рекомендациями.