Дорогие Гуры поможите пожалуста.Поставил FREEBSD 7.1
Пытаюсь настроить разадчу инета в локалку через PPPoE
1.Через PPPoE конектится
2.с FreeBSD ping идет
3. С сетки не идет ping и инет
Прилагаю конфиги
rc.conf
# -- sysinstall generated deltas -- # Sat Feb 21 21:24:37 2009
# Created: Sat Feb 21 21:24:37 2009
# Enable network daemons for user convenience.
# Please make all changes to this file, not to /etc/defaults/rc.conf.
# This file now contains just the overrides from /etc/defaults/rc.conf.
hostname="freebsd.home"
ifconfig_em0="inet 192.168.1.150 netmask 255.255.255.0"
ifconfig_em1="inet "
webmin_enable="YES"
gateway_enable="YES"
mpd_enable="YES"
pf_enable="YES"
pf_rules="/etc/pf.conf"
pf_flags=""
pflog_enable="YES"
pflog_logfile="/var/log/pflog"
pflog_flags=""
---------------------------------------------------------------------------------
pf.conf
ext_if="ng0"
int_if="em0
altq on
scrub in all
nat on $ext_if from $int_if:network to any -> ($ext_if)
pass in all keep state
pass out all keep state
-----------------------------------------------------------------
mpd.conf
default:
load PPPoE
PPPoE:
new -i ng0 PPPoE PPPoE
set link mtu 1492
set iface route default
set iface enable tcpmssfix
set iface disable on-demand
set iface idle 0
set bundle disable multilink
set bundle authname "ao004584@dsl.ukrtel.net"
set bundle password "95214832"
set link no acfcomp protocomp
set link disable pap chap
set link accept chap
set link keep-alive 10 60
set ipcp yes vjcomp
set ipcp ranges 0.0.0.0/0 0.0.0.0/0
open iface
--------------------------------------------------------------
mpd.links
PPPoE:
set link type pppoe
set pppoe iface em1:
set pppoe service ""
set pppoe disable incoming
set pppoe enable originate
------------------------------------------------------------------
Вот что выдает ifconfig
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
ether 00:0c:29:c9:f6:99
inet 192.168.1.150 netmask 0xffffff00 broadcast 192.168.1.255
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: active
em1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
ether 00:0c:29:c9:f6:a3
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: active
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33204
ng0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> metric 0 mtu 1492
inet 92.113.39.90 --> 195.5.5.202 netmask 0xffffffff
-------------------------------------------------------------------------------
Лазил по манулам читал форумы не знаю что делать !!!
Что я не так сделал ?
