18.5 Using PPP over ATM (PPPoA)
The following describes how to set up PPP over ATM (PPPoA). PPPoA is a popular choice among European DSL providers.
18.5.1 Using PPPoA with the Alcatel Speedtouch USB
PPPoA support for this device is supplied as a port in FreeBSD because the firmware is distributed under Alcatel's license agreement and can not be redistributed freely with the base system of FreeBSD.
To install the software, simply use the ports collection. Install the net/pppoa port and follow the instructions provided with it.
18.5.2 Using mpd
You can use mpd to connect to a variety of services, in particular pptp services. You can find mpd in the ports collection, net/mpd.
First you must install the port, and then you can configure mpd to suit your requirements and provider settings. The port places a set of sample configuration files which are well documented in PREFIX/etc/mpd/. Note here that PREFIX means the directory into which your ports are installed, this defaults to /usr/local/. A complete guide to configuring mpd is available in HTML format once the port has been installed. It is placed in PREFIX/share/mpd/. Here is a sample configuration for connecting to an ADSL service with mpd. The configuration is spread over two files, first the mpd.conf.
default:
load adsl
adsl:
new -i ng0 adsl adsl
set bundle authname username 
set bundle password password 
set bundle disable multilink
set link no pap actcomp protocomp
set link disable chap
set link accept chap
set link keep-alive 30 10
set ipcp no vjcomp
set ipcp ranges 0.0.0.0/0 0.0.0.0/0
set iface route default
set iface disable on-demand
set iface enable proxy-arp
set iface idle 0
open
- The username used to authenticate with your ISP.
- The password used to authenticate with your ISP.
The mpd.links file contains information about the link, or links, you wish to establish. An example mpd.links to accompany the above example is given beneath.
adsl:
set link type pptp
set pptp mode active
set pptp enable originate incoming outcall
set pptp self 10.0.0.140
set pptp peer 10.0.0.138
It is possible to initialise the connection easily by issuing the following command as root.
# mpd -b adsl
You can see the status of the connection with the following command.
% ifconfig ng0
: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> mtu 1500
inet 216.136.204.117 --> 204.152.186.171 netmask 0xffffffff
Using mpd is the recommended way to connect to an ADSL service with FreeBSD.
18.5.3 Using pptpclient
It is also possible to use FreeBSD to connect to other PPPoA services using net/pptpclient.
To use net/pptpclient to connect to a DSL service, install the port or package and edit your /etc/ppp/ppp.conf. You will need to be root to perform both of these operations. An example section of ppp.conf is given below. For further information on ppp.conf options consult the ppp manual page, ppp(8).
adsl:
set log phase chat lcp ipcp ccp tun command
set timeout 0
enable dns
set authname username
set authkey password
set ifaddr 0 0
add default HISADDR
- The username of your account with the DSL provider.
- The password for your account.
Warning: Because you must put your account's password in the ppp.conf file in plain text form you should make sure than nobody can read the contents of this file. The following series of commands will make sure the file is only readable by the root account. Refer to the manuals pages for chmod(1) and chown(8) for further information.
# chown root:wheel /etc/ppp/ppp.conf # chmod 600 /etc/ppp/ppp.conf
This will open a tunnel for a PPP session to your DSL router. Ethernet DSL modems have a preconfigured LAN IP address which you connect to. In the case of the Alcatel Speedtouch Home this address is 10.0.0.138. Your routers documentation should tell you which address your device uses. To open the tunnel and start a ppp session execute the following command.
# pptp address isp
Tip: You may wish to add an ampersand (``&'') to the end of the previous command because pptp will not return your prompt to you otherwise.
A tun virtual tunnel device will be created for interaction between the pptp and ppp processes. Once you have been returned to your prompt, or the pptp process has confirmed a connection you can examine the tunnel like so.
% ifconfig tun0
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
inet 216.136.204.21 --> 204.152.186.171 netmask 0xffffff00
Opened by PID 918
If you are unable to connect, check the configuration of your router, which is usually accessible via telnet or with a web browser. If you still cannot connect you should examine the output of the pptp command and the contents of the ppp log file, /var/log/ppp.log for clues.
