The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

newfs (8)
  • newfs (1) ( Solaris man: Команды и прикладные программы пользовательского уровня )
  • >> newfs (8) ( FreeBSD man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    newfs
    
     - construct a new UFS1/UFS2 file system
    
     
    

    SYNOPSIS

    [-JNUln ] [-L volname ] [-O filesystem-type ] [-S sector-size ] [-T disktype ] [-a maxcontig ] [-b block-size ] [-c blocks-per-cylinder-group ] [-d max-extent-size ] [-e maxbpg ] [-f frag-size ] [-g avgfilesize ] [-h avgfpdir ] [-i bytes ] [-m free-space ] [-o optimization ] [-s size ] special  

    DESCRIPTION

    The utility is used to initialize and clear file systems before first use. Before running the disk must be labeled using bsdlabel(8). The utility builds a file system on the specified special file. (We often refer to the ``special file'' as the ``disk'' although the special file need not be a physical disk. In fact, it need not even be special.) Typically the defaults are reasonable, however has numerous options to allow the defaults to be selectively overridden.

    The following options define the general layout policies:

    -J
    Enable journaling on the new file system via gjournal.
    -L volname
    Add a volume label to the new file system.
    -N
    Cause the file system parameters to be printed out without really creating the file system.
    -O filesystem-type
    Use 1 to specify that a UFS1 format file system be built; use 2 to specify that a UFS2 format file system be built. The default format is UFS2.
    -T disktype
    For backward compatibility.
    -U
    Enable soft updates on the new file system.
    -a maxcontig
    Specify the maximum number of contiguous blocks that will be laid out before forcing a rotational delay. The default value is 16. See tunefs(8) for more details on how to set this option.
    -b block-size
    The block size of the file system, in bytes. It must be a power of 2. The default size is 16384 bytes, and the smallest allowable size is 4096 bytes. The optimal block:fragment ratio is 8:1. Other ratios are possible, but are not recommended, and may produce poor results.
    -c blocks-per-cylinder-group
    The number of blocks per cylinder group in a file system. The default is to compute the maximum allowed by the other parameters. This value is dependent on a number of other parameters, in particular the block size and the number of bytes per inode.
    -d max-extent-size
    The file system may choose to store large files using extents. This parameter specifies the largest extent size that may be used. It is presently limited to its default value which is 16 times the file system blocksize.
    -e maxbpg
    Indicate the maximum number of blocks any single file can allocate out of a cylinder group before it is forced to begin allocating blocks from another cylinder group. The default is about one quarter of the total blocks in a cylinder group. See tunefs(8) for more details on how to set this option.
    -f frag-size
    The fragment size of the file system in bytes. It must be a power of two ranging in value between blocksize /8 and blocksize The default is 2048 bytes.
    -g avgfilesize
    The expected average file size for the file system.
    -h avgfpdir
    The expected average number of files per directory on the file system.
    -i bytes
    Specify the density of inodes in the file system. The default is to create an inode for every (4 * frag-size ) bytes of data space. If fewer inodes are desired, a larger number should be used; to create more inodes a smaller number should be given. One inode is required for each distinct file, so this value effectively specifies the average file size on the file system.
    -l
    Enable multilabel MAC on the new file system.
    -m free-space
    The percentage of space reserved from normal users; the minimum free space threshold. The default value used is defined by MINFREE from In ufs/ffs/fs.h , currently 8%. See tunefs(8) for more details on how to set this option.
    -n
    Do not create a .snap directory on the new file system. The resulting file system will not support snapshot generation, so dump(8) in live mode and background fsck(8) will not function properly. The traditional fsck(8) and offline dump(8) will work on the file system. This option is intended primarily for memory or vnode-backed file systems that do not require dump(8) or fsck(8) support.
    -o optimization
    ( space or time ) The file system can either be instructed to try to minimize the time spent allocating blocks, or to try to minimize the space fragmentation on the disk. If the value of minfree (see above) is less than 8%, the default is to optimize for space if the value of minfree is greater than or equal to 8%, the default is to optimize for time See tunefs(8) for more details on how to set this option.
    -s size
    The size of the file system in sectors. This value defaults to the size of the raw partition specified in special (in other words, will use the entire partition for the file system).

    The following options override the standard sizes for the disk geometry. Their default values are taken from the disk label. Changing these defaults is useful only when using to build a file system whose raw image will eventually be used on a different type of disk than the one on which it is initially created (for example on a write-once disk). Note that changing any of these values from their defaults will make it impossible for fsck(8) to find the alternate superblocks if the standard superblock is lost.

    -S sector-size
    The size of a sector in bytes (almost never anything but 512).

     

    EXAMPLES

    newfs /dev/ad3s1a

    Creates a new ufs file system on ad3s1a The utility will use a block size of 16384 bytes, a fragment size of 2048 bytes and the largest possible number of blocks per cylinders group. These values tend to produce better performance for most applications than the historical defaults (8192 byte block size and 1024 byte fragment size). This large fragment size may lead to much wasted space on file systems that contain many small files.  

    SEE ALSO

    fdformat(1), disktab(5), fs(5), bsdlabel(8), camcontrol(8), dump(8), dumpfs(8), fsck(8), mount(8), tunefs(8), gvinum(8)
    M. McKusick W. Joy S. Leffler R. Fabry A Fast File System for UNIX ACM Transactions on Computer Systems 2 3 pp 181-197 August 1984 (reprinted in the BSD System Manager's Manual)
     

    HISTORY

    The utility appeared in BSD 4.2


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    EXAMPLES
    SEE ALSO
    HISTORY


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру